|
|
Introduction of the New Technology into the Company
Vondruška, Jiří ; Růčka, Pavel (referee) ; Šunka, Josef (advisor)
The work is focused on introduction of new technology to the company engaged in dyeing and finishing of textile materials. The aim is to determine whether the investment will be beneficial for the company. Therefore it is necessary to learn about functioning of the company, with market, that is about to enter, with the reasons for choosing of the specific technology, way of financing, but also with technology itself. Subsequently it is needed to determine whether the investment will be effective or not.
|
|
|
Locomotive power transmission
Svoboda, Petr ; Knotek, Jiří (referee) ; Zubík, Martin (advisor)
The work describes the specific conditions for transmission devices in railway operations. It includes the description, distinction and comparison of power-transfering possibilities from the rail vehicle's combustion engine to the propelled chassis.
|
|
|
Reduction of Contact Pairs Friction Losses
Novotný, Marek ; Raffai, Peter (referee) ; Maršálek, Ondřej (advisor)
This bachelor thesis deals with the topic of mechanical efficiency of contact pairs in the crankshaft of the combustion engine. The introductory section focuses on the efficiency of the combustion engine as a whole. In addition, it describes the areas where mechanical losses primarily occur. The following chapters describe mechanism of friction losses, the main factors affecting their amount and the most modern ways to increase mechanical efficiency. In the closing chapter, some basic computing relations, describing the size of mechanical losses are listed. The aim of this thesis is to acquaint the reader with the importance of mechanical efficiency in the area of combustion engines.
|
|
|
Analysis of the steam engine for combined heat and power
Uryč, Jan ; Fiedler, Jan (referee) ; Škorpík, Jiří (advisor)
In some applications, the piston steam engine may be more suitable than the technology currently used. The thesis deals with the analysis of its advantages, weaknesses and possibilities of use, which are offered. Introduces the principles and functions of piston steam engines. It also contains a thermodynamic design based on a specific assignment and a feasibility assessment.
|
|
|
Single-Phase Induction Motor
Vácha, Pavel ; Lapčík, Josef (referee) ; Hájek, Vítězslav (advisor)
The bachelor work is concerned the thesis of a single-phase induction motor that´s perpetually more used in all over the world. Its aim is assembling the information about this type of motor and its calculation. The content of the first part is the theoretical analysis of a single-phase induction motor and acquirement ways of the stroke moment. The practical part contains a basic schema calculation of the single-phase induction motor with an auxiliary phase and a processing demonstrate example of calculation of the single-phase induction motor with concrete parameters along suggested process. In the conclusion there is the evaluation of the whole process.
|
|
|
Fluid couplings and torque convertors
Skokan, Jan ; Jandourek, Pavel (referee) ; Klas, Roman (advisor)
This bachelor thesis is devoted to the issue of fluid couplings and torque convertorsand their combination with mechanical gears. The main section outlines development and design of fluid couplings and torque convertors.Resources to improve their performance are also mentioned. Furthermore, there are mentioned combinations of fluid and mechanical transmission.
|
|
| |
|
|
Tesla Bladeless Turbine
Lokaj, Jakub ; Kracík, Petr (referee) ; Fiedler, Jan (advisor)
The diploma thesis describes design of bladeless machine known as a Tesla turbine. The work is divided into theoretical part, practical part involving the design and experimental measurements of made bladeless turbine and a final assessment of thesis. The theoretical part deals with the basic design features of bladeless machines and their design modifications and flow in the nozzles. Furthermore there is a dedicated part of the dynamics of working fluid in the rotor of bladeless turbine represented by CFD modeling. The practical part includes the design and construction of parts of the turbine on a preliminary calculation using an analytical model of the flow in the turbine. The designed turbine components were checked for operational safety with structural calculations of shaft and disk impeller. The thesis was also performed experimental measuring of parameters of designed bladeless turbine. Measured values were compared with the analytical model which predicted turbine efficiency. In conclusion, besides to assessment, thesis also outlines possible proposals for further improvements of constructed bladeless turbine.
|
|
|
Theoretical use of nanotechnology for filtration in HVAC systems
Bosák, Jan ; Ell, Jiří (referee) ; Rubina, Aleš (advisor)
Thesis solves problems using the nanotechnology for air filtration in HVAC systems. Main specialization work is air filtration for clean spaces with high classes of purity. For example Hospitals, sophisticated technology service, pharmacy etc. Thesis is devide for three parts. First part contains foundation infromations about theory and making fabrics by nanotechnology. Next I described laws of physics, That were using during the solving filtration´s issues. Goal for second part was making the experiments, which should show abilities and properties nanofilters during the air filtration in real environment HVAC systems. In the end measure part is compare nanofilters with common filters. There is describe nanofiltres behavior and their possibilies during the filtration as well as. In last part I expressed own opinions on air filtration by nanofibers. Opinions were making throught informations, That I found out in the process working on thesis and my experiences in HVAC field. By this facts I did compare for get a better idea. Additionally last part contains summary infomations from previously parts and own vision to development in the future. Goal work isn´t promotion and advertising sorts technologies. Ask is just summary and describe discovered knowledges, considered opinions ensue from measuring, information from the Net and people Who work in nanotechnology field.
|
|
|
Single-Phase Induction Motor Calculation
Vácha, Pavel ; Vítek, Ondřej (referee) ; Hájek, Vítězslav (advisor)
The master´s thesis deal with the thesis of a single-phase induction motor that is more and more used all over the world. Its aim is assembling the information about this type of motor and its calculation. The content of the first part is the theoretical analysis of a single-phase induction motor and acquirement ways of the stroke moment. Than the work contains a project of basic schema of the single-phase induction motor with an auxiliary phase. The practical part is devoted to an elaboration of demonstration example of the single-phase induction motor with concrete parameters calculation, its method was projected before. Than there is practising successived measuring on the motor of the same parameters made firm EMP s.r.o. Slavkov by Brno in this part. In the conclusion there is the evaluation of the whole process with reached results.
|
guest ::
